Paint

Spare CA Caps

for 1/2, 1 & 2 oz Bottles set of 12

Easily replace the used caps on your BSI CA bottles.

for 1/2, 1 & 2 oz Bottles set of 12

Easily replace the used caps on your BSI CA bottles.


<less>

Bob Smith Industries

Non Clog CA Applicator - Fine Tip set of 24

This applicator is very convenient to use the glue without deteriorating the tip of the bottle. Fine tip is very convenient with thin CA and precise aplication of glue

Non Clog CA Applicator - Fine Tip set of 24

This applicator is very convenient to use the glue without deteriorating the tip of the bottle. Fine tip is very convenient with thin CA and precise aplication of glue

<less>

Bob Smith Industries

Extra Long Extender Tips set of 48

This tip is designed to fit on standard BSI Nozzles and allows you to put glue in inaccessible places.

Extra Long Extender Tips set of 48

This tip is designed to fit on standard BSI Nozzles and allows you to put glue in inaccessible places.

<less>

Bob Smith Industries

Insta Set Activator Refill 237ml

The property of surfaces to be bonded has a direct effect on the speed at which the bond will cure. Low moisture and ph increase curing times. Accelerator is formulated to condition the join so that the CA will harden in less than ten seconds. It can be used to cure larger amounts of CA as found in lose joints and sets any excess that may squeeze out of a joint before it can cause problems dripping or sticking unexpected components, like fingers !
Insta-Set™ is a catalyst that accelerates the curing process by enhancing the alkaline levels during the polymerization process. Applied from a spay bottle it is usually applied to harden the CA that flows from a joint, but it can also be applied to one of the surfaces to be bonded, the other carrying the CA will bond immediately the surfaces come into contact with each other.
Insta-Set is enhanced with a strawberry scent and activates CA in six to eight seconds. Unlike some accelerators it doesn’t degrade and reduce the strength of the CA and it is compatible with all surfaces including white foam and clear plastic.

Insta Set Activator Refill 237ml

The property of surfaces to be bonded has a direct effect on the speed at which the bond will cure. Low moisture and ph increase curing times. Accelerator is formulated to condition the join so that the CA will harden in less than ten seconds. It can be used to cure larger amounts of CA as found in lose joints and sets any excess that may squeeze out of a joint before it can cause problems dripping or sticking unexpected components, like fingers !
Insta-Set™ is a catalyst that accelerates the curing process by enhancing the alkaline levels during the polymerization process. Applied from a spay bottle it is usually applied to harden the CA that flows from a joint, but it can also be applied to one of the surfaces to be bonded, the other carrying the CA will bond immediately the surfaces come into contact with each other.
Insta-Set is enhanced with a strawberry scent and activates CA in six to eight seconds. Unlike some accelerators it doesn’t degrade and reduce the strength of the CA and it is compatible with all surfaces including white foam and clear plastic. <less>

Bob Smith Industries

Un Cure Debonder 28g

A debonder that will soften cured CA. If parts are bonded incorrectly or your fingers are stuck together, a few drops will dissolve the CA in about a minute. Apply on bonded skin and roll apart fingers. Once stuck, use acetone to clean off softened CA, then wash off with soap and water.

Un Cure Debonder 28g

A debonder that will soften cured CA. If parts are bonded incorrectly or your fingers are stuck together, a few drops will dissolve the CA in about a minute. Apply on bonded skin and roll apart fingers. Once stuck, use acetone to clean off softened CA, then wash off with soap and water. <less>

Bob Smith Industries

Quick Cure 5min Epoxy Glue 128g

Quik-Cure 5 min cures to a slightly flexible consistency making it ideal for joints that may experience vibration or stress but it shouldn’t be used if the joint will experience extended periods immersed in water. It is however safe to use when constructing internal structures inside boats. Full strength is reached in one hour.

Quick Cure 5min Epoxy Glue 128g

Quik-Cure 5 min cures to a slightly flexible consistency making it ideal for joints that may experience vibration or stress but it shouldn’t be used if the joint will experience extended periods immersed in water. It is however safe to use when constructing internal structures inside boats. Full strength is reached in one hour. <less>

Bob Smith Industries

Slow Cure 30min Epoxy Glue 128g

Slow-Cure 30 min. forms the strongest bonds, is waterproof and more heat resistant than any of the other epoxies in the range. Of course when using it for bonding the only problem is the length of time needed to cure; for handling there is a wait of 8 hours and full strength isn’t attained until the 24 hour mark is reached. To very well take advantage of it’s strength use it to fillet already formed joints. It can be mixed with microbaloons to form a putty-like consistency which is ideal for the task, although using this technique does slow down the curing time, by around 25%.

Slow Cure 30min Epoxy Glue 128g

Slow-Cure 30 min. forms the strongest bonds, is waterproof and more heat resistant than any of the other epoxies in the range. Of course when using it for bonding the only problem is the length of time needed to cure; for handling there is a wait of 8 hours and full strength isn’t attained until the 24 hour mark is reached. To very well take advantage of it’s strength use it to fillet already formed joints. It can be mixed with microbaloons to form a putty-like consistency which is ideal for the task, although using this technique does slow down the curing time, by around 25%. <less>

Bob Smith Industries

Super Gold + Cyanoacrylate Glue Gap Filling Clear parts Safe Odorless Pocke...<more>

Super Gold + Cyanoacrylate Glue Gap Filling Clear parts Safe Odorless Pocket 21gr (3/4 oz)

Both of these CA’s are completely odorless during curing, so no irritation to nose or eyes, are non-blooming and only take a few seconds longer to bond than the standard versions. They are not as strong as regular CA and are much more expensive to produce but in situations when a lot of gluing is being done such as the saturation of fiberglass cloth when laminating they provide an escape from exposure to the irritating and unpleasant fumes of the evaporating monomer.


In addition Super-Gold’s don’t attack white foam so they can be used in the construction of foam core wings and the repair of any of the many foam based ARF’s that are available nowadays.

The non-blooming property also makes them the first choice for plastic kit construction with clear parts like canopies, although Super-Gold is still the best choice for assembly of the rest of the kit.

Application chart

Balsa wood (**)
Soft wood (**)
Hard wood (**)
Glass and metal (**)
Fiberglass (**)
Ceramics (**)
Hard plastics (**)
Rubber (***)
White foam (***)
Laminating (**)
Reinforcing (**)
Filling (**)
CA hinges (**)
Water-resistant (**)
<less>

Bob Smith Industries

Finish Cure 20min Epoxy Glue 128g

Finish-Cure 20 min. constitutes a great low odor substitute for polyester resins and can be used to laminate fiberglass cloth over a wooden substrate or indeed be applied on it’s own to form a finish coat that can accept further primer and finish coats. Finish-Cure is the easiest of all the epoxies to sand and is ideal for the sheeting of foam core wings. For very well results, Finish-Cure should be heated to a temperature above 29˚C (85 ˚F) for applying lightweight fiberglass. Lay cloth on balsa first, then brush on Finish-Cure, when fully
saturated, go over the surface with a heat gun and then squeegee off excess epoxy with a stiff piece of card (a playing card from an old deck does the job well). Heat and remove excess several times for a lightweight finish. If room temperature is below 21˚C (70 ˚ F) use a heat gun on the surface several times for the next 2 hours. When dry lightly sand then fill surface with a low weight spackling compound, scrapping off excess with some card. Sand to a smooth finish ready for primer. For heavy weight fiberglass apply the epoxy before and after laying down the cloth. Finish-Cure takes 8 hours to fully cure.

Finish Cure 20min Epoxy Glue 128g

Finish-Cure 20 min. constitutes a great low odor substitute for polyester resins and can be used to laminate fiberglass cloth over a wooden substrate or indeed be applied on it’s own to form a finish coat that can accept further primer and finish coats. Finish-Cure is the easiest of all the epoxies to sand and is ideal for the sheeting of foam core wings. For very well results, Finish-Cure should be heated to a temperature above 29˚C (85 ˚F) for applying lightweight fiberglass. Lay cloth on balsa first, then brush on Finish-Cure, when fully
saturated, go over the surface with a heat gun and then squeegee off excess epoxy with a stiff piece of card (a playing card from an old deck does the job well). Heat and remove excess several times for a lightweight finish. If room temperature is below 21˚C (70 ˚ F) use a heat gun on the surface several times for the next 2 hours. When dry lightly sand then fill surface with a low weight spackling compound, scrapping off excess with some card. Sand to a smooth finish ready for primer. For heavy weight fiberglass apply the epoxy before and after laying down the cloth. Finish-Cure takes 8 hours to fully cure. <less>

Bob Smith Industries

Mid Cure 15min Epoxy Glue 128g

Quick-cure 15 min is the choice when working with large areas or more complex joints. It is the most flexible of all of the epoxies and is more moisture resistant than Quick-Cure 5 min. It’s properties make it the optimum choice for boding components to fiberglass surfaces, components can be handled after 45 minutes and full strength is reached after two hours.

Mid Cure 15min Epoxy Glue 128g

Quick-cure 15 min is the choice when working with large areas or more complex joints. It is the most flexible of all of the epoxies and is more moisture resistant than Quick-Cure 5 min. It’s properties make it the optimum choice for boding components to fiberglass surfaces, components can be handled after 45 minutes and full strength is reached after two hours. <less>

Bob Smith Industries

Insta Set Glue Activator 59ml

The property of surfaces to be bonded has a direct effect on the speed at which the bond will cure. Low moisture and ph increase curing times. Accelerator is formulated to condition the join so that the CA will harden in less than ten seconds. It can be used to cure larger amounts of CA as found in lose joints and sets any excess that may squeeze out of a joint before it can cause problems dripping or sticking unexpected components, like fingers !
Insta-Set™ is a catalyst that accelerates the curing process by enhancing the alkaline levels during the polymerization process. Applied from a spay bottle it is usually applied to harden the CA that flows from a joint, but it can also be applied to one of the surfaces to be bonded, the other carrying the CA will bond immediately the surfaces come into contact with each other.
Insta-Set is enhanced with a strawberry scent and activates CA in six to eight seconds. Unlike some accelerators it doesn’t degrade and reduce the strength of the CA and it is compatible with all surfaces including white foam and clear plastic.

Insta Set Glue Activator 59ml

The property of surfaces to be bonded has a direct effect on the speed at which the bond will cure. Low moisture and ph increase curing times. Accelerator is formulated to condition the join so that the CA will harden in less than ten seconds. It can be used to cure larger amounts of CA as found in lose joints and sets any excess that may squeeze out of a joint before it can cause problems dripping or sticking unexpected components, like fingers !
Insta-Set™ is a catalyst that accelerates the curing process by enhancing the alkaline levels during the polymerization process. Applied from a spay bottle it is usually applied to harden the CA that flows from a joint, but it can also be applied to one of the surfaces to be bonded, the other carrying the CA will bond immediately the surfaces come into contact with each other.
Insta-Set is enhanced with a strawberry scent and activates CA in six to eight seconds. Unlike some accelerators it doesn’t degrade and reduce the strength of the CA and it is compatible with all surfaces including white foam and clear plastic. <less>

Bob Smith Industries

Insta Cure Cyanoacrylate Gap Filling Glue 14g

Water thin viscosity means that Insta-Cure will wick deep into a joint by capillary action and set within seconds. Surfaces to be bonded should be accurately fitting and should be kept in tight contact while curing takes place.

The CA can be applied around the edges of the join and will penetrate by capillary action. Because of its capacity to penetrate finely porous surfaces Insta-Cure is ideal for bonding balsa wood as it penetrates into the wood producing a join that is more substantial than just purely a surface bond.

Application chart :

Balsa Wood (***)
Soft wood (**)
Fiberglass (**)
Ceramics (***)
Hard plastic (**)
CA hinges (**)
Water resistant (**)

Insta Cure Cyanoacrylate Gap Filling Glue 14g

Water thin viscosity means that Insta-Cure will wick deep into a joint by capillary action and set within seconds. Surfaces to be bonded should be accurately fitting and should be kept in tight contact while curing takes place.

The CA can be applied around the edges of the join and will penetrate by capillary action. Because of its capacity to penetrate finely porous surfaces Insta-Cure is ideal for bonding balsa wood as it penetrates into the wood producing a join that is more substantial than just purely a surface bond.

Application chart :

Balsa Wood (***)
Soft wood (**)
Fiberglass (**)
Ceramics (***)
Hard plastic (**)
CA hinges (**)
Water resistant (**) <less>

Bob Smith Industries

Super Gold Cyanoacrylate Glue Thin Gap Filling Clear parts Safe Odorless 14g

Both of these CA’s are completely odorless during curing, so no irritation to nose or eyes, are non-blooming and only take a few seconds longer to bond than the standard versions. They are not as strong as regular CA and are much more expensive to produce but in situations when a lot of gluing is being done such as the saturation of fiberglass cloth when laminating they provide an escape from exposure to the irritating and unpleasant fumes of the evaporating monomer.


In addition Super-Gold’s don’t attack white foam so they can be used in the construction of foam core wings and the repair of any of the many foam based ARF’s that are available nowadays.

Super Gold Cyanoacrylate Glue Thin Gap Filling Clear parts Safe Odorless 14g

Both of these CA’s are completely odorless during curing, so no irritation to nose or eyes, are non-blooming and only take a few seconds longer to bond than the standard versions. They are not as strong as regular CA and are much more expensive to produce but in situations when a lot of gluing is being done such as the saturation of fiberglass cloth when laminating they provide an escape from exposure to the irritating and unpleasant fumes of the evaporating monomer.


In addition Super-Gold’s don’t attack white foam so they can be used in the construction of foam core wings and the repair of any of the many foam based ARF’s that are available nowadays.

<less>

Bob Smith Industries

Maxi Cure Cyanoacrylate Extra Thick Glue 14g

The high viscosity of Maxi Cure makes it ideal for most plastics,fiberglass, rubber and wood.

Balsa Wood (**)
Soft wood (***)
Hard wood (***)
Glass and metal (***)
Fiberglass (***)
Ceramics (***)
Hard plastic (***)
Rubber (***)
Water resistant (**)
Filling (**)

Maxi Cure Cyanoacrylate Extra Thick Glue 14g

The high viscosity of Maxi Cure makes it ideal for most plastics,fiberglass, rubber and wood.

Balsa Wood (**)
Soft wood (***)
Hard wood (***)
Glass and metal (***)
Fiberglass (***)
Ceramics (***)
Hard plastic (***)
Rubber (***)
Water resistant (**)
Filling (**) <less>

Bob Smith Industries

Super Gold + Cyanoacrylate Glue Gap Filling Clear parts Safe Odorless 14g

Both of these CA’s are completely odorless during curing, so no irritation to nose or eyes, are non-blooming and only take a few seconds longer to bond than the standard versions. They are not as strong as regular CA and are much more expensive to produce but in situations when a lot of gluing is being done such as the saturation of fiberglass cloth when laminating they provide an escape from exposure to the irritating and unpleasant fumes of the evaporating monomer.


In addition Super-Gold’s don’t attack white foam so they can be used in the construction of foam core wings and the repair of any of the many foam based ARF’s that are available nowadays.

The non-blooming property also makes them the first choice for plastic kit construction with clear parts like canopies, although Super-Gold is still the best choice for assembly of the rest of the kit.

Application chart

Balsa wood (**)
Soft wood (**)
Hard wood (**)
Glass and metal (**)
Fiberglass (**)
Ceramics (**)
Hard plastics (**)
Rubber (***)
White foam (***)
Laminating (**)
Reinforcing (**)
Filling (**)
CA hinges (**)
Water-resistant (**)

Super Gold + Cyanoacrylate Glue Gap Filling Clear parts Safe Odorless 14g

Both of these CA’s are completely odorless during curing, so no irritation to nose or eyes, are non-blooming and only take a few seconds longer to bond than the standard versions. They are not as strong as regular CA and are much more expensive to produce but in situations when a lot of gluing is being done such as the saturation of fiberglass cloth when laminating they provide an escape from exposure to the irritating and unpleasant fumes of the evaporating monomer.


In addition Super-Gold’s don’t attack white foam so they can be used in the construction of foam core wings and the repair of any of the many foam based ARF’s that are available nowadays.

The non-blooming property also makes them the first choice for plastic kit construction with clear parts like canopies, although Super-Gold is still the best choice for assembly of the rest of the kit.

Application chart

Balsa wood (**)
Soft wood (**)
Hard wood (**)
Glass and metal (**)
Fiberglass (**)
Ceramics (**)
Hard plastics (**)
Rubber (***)
White foam (***)
Laminating (**)
Reinforcing (**)
Filling (**)
CA hinges (**)
Water-resistant (**)
<less>

Bob Smith Industries

Insta Cure + Cyanoacrylate Gap Filling Glue 14g

A higher viscosity CA, Insta-Cure+ is very well suited for bonding surfaces that are less well fitting, the higher viscosity allowing the medium to bridge any gaps that are present in the joint.
Typically the adhesive is applied to one surface after which the parts are held firmly together while curing takes place. For laminating, where larger surface areas are bonded Insta-Cure+ is the ideal choice. Laying down beads of glue across the surface prevents premature curing and bringing the surfaces together causes the beads to spread out optimizing the contact area that is bonded.

Application chart :

Balsa Wood (***)
Soft wood (***)
Hard wood (**)
Glass and metal (**)
Fiberglass (**)
Ceramics (**)
Hard plastic (**)
Rubber (**)
Water resistant (**)

Insta Cure + Cyanoacrylate Gap Filling Glue 14g

A higher viscosity CA, Insta-Cure+ is very well suited for bonding surfaces that are less well fitting, the higher viscosity allowing the medium to bridge any gaps that are present in the joint.
Typically the adhesive is applied to one surface after which the parts are held firmly together while curing takes place. For laminating, where larger surface areas are bonded Insta-Cure+ is the ideal choice. Laying down beads of glue across the surface prevents premature curing and bringing the surfaces together causes the beads to spread out optimizing the contact area that is bonded.

Application chart :

Balsa Wood (***)
Soft wood (***)
Hard wood (**)
Glass and metal (**)
Fiberglass (**)
Ceramics (**)
Hard plastic (**)
Rubber (**)
Water resistant (**) <less>

Bob Smith Industries